TP-Link JetStream 24-Port Gigabit L2 Managed Switch with 4 SFP Slots, Supports 24 Gigabit RJ45 ports, Rackmount (TL-SG3428)

Product Information

Use the enable command to enter this mode from User EXEC mode, which allows more commands such as “configure”. It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade. Note, if you enter an abbreviation that corresponds to more than one command, the switch will not be able to recognize the command you are trying to execute and you need to enter more.

Using Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 07-07-2023 17569 Using the Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 06-08-2023 17569 Come gestire i dispositivi Omada in diversi siti utilizzando il Controller Omada SDN via VPN (Controller 5.0 o successivo) 05-02-2023 17174 You can use the Auto-Completion feature to enter a complete command, you can also enter part of the command without completion, and the switch will recognize and execute the command automatically. The switchport general allowed command is used to add a port to a VLAN and set the tagged/untagged mode. To remove a port for a VLAN, please use no switchport general allowed command.

A firmware update can resolve issues that the previous firmware version may have and improve its current performance. To Upgrade

What's the difference between Master Administrator, Administrator and Viewer account in Omada Controller? 04-20-2023 16282 Note that TP-Link switches use Auto duplex mode by default and it is recommended to keep the mode if there are no connection problems.

Advanced L3 Features**

Ports 2, 3, 4 are used as access ports to connect computers. The following configurations describe how to add port 2, 3, 4 to the corresponding VLANs and set PVIDs. IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process If your computer has a serial port (COM), please connect it to the console port (RJ45) of the switch, with the RJ45 console cable. Using the Omada SDN Controller to Manage Omada Devices Across Multiple Locations Via a Controller (5.0 and Above) 05-31-2023 20224

Come configurare lo snooping IGMP per la rete IPTV sugli switch gestiti L2 usando la nuova GUI? 01-05-2021 139402 Use the command “ip igmp snooping” to globally enable the function. There are three versions of IGMP, the default version is v3, which supports to process IGMP v1, v2, and v3 report messages from the host, thus normally there is no need to modify the version.The switch supports configuring IGMP Snooping on a per-VLAN basis. After IGMP Snooping is enabled globally, you also need to enable IGMP Snooping and configure the corresponding parameters for the VLANs that the router ports and the member ports are in. The command is “ip igmp snooping vlan-config vlan-id”. A commonly used option is “Unknown Multicast Groups”, by default, it is Forward, which means the switch forwards the multicast streams that are sent to unknown multicast groups. You can change the option to Discard so that the switch discards the multicast streams. Note to discard them, you need to enable MLD Snooping first. You can enable Fast Leave by enabling the feature for both the VLAN and the Port when there is only one client connected to the access port. IGMP Snooping helps the switch maintain a multicast forwarding table by snooping the IGMP transmission between the host and the IGMP Querier. With the forwarding table, the switch can forward multicast data only to the ports that are in the corresponding multicast group, to constrain the flooding of multicast data in the Layer 2 network. V2: 1589.31 BTU/hr (110 V/60 Hz) (with 384 W PD connected); 117.38 BTU/hr (110 V/60 Hz) (no PD connected)

How to enter the BootUtil Menu to factory reset the switch with the console cable? 09-06-2021 78714 Qual è la differenza tra gli account Master Administrator, Administrator e Viewer in Omada Controller? 04-14-2023 16282 After entering part of a command, you can press the TAB key or a question mark (?) then the switch will automatically complete the command. If your input corresponds to more than one command, the switch will not auto-complete but will display all related commands. This guide is intended to provide network administrators with some typical examples of CLI (Command Line Interface) configuration. Normally, all switch ports are member ports of VLAN 1. If you do not want to remove a port from VLAN 1, you need to additionally configure it.Using the Omada SDN Controller to Manage Omada Devices Across Multiple Locations Via a VPN Connection (Controller 5.0 and Above) 05-05-2023 17174 A querier periodically sends a general query on the network to solicit membership information and sends group-specific queries when it receives leave messages from hosts. Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. ( Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28) To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device. Note the Ethernet port type in the command is the native speed mode of the ports, not the current operating mode. For example, assuming the current speed mode of SFP+ port 25 is 1Gbps, to configure it, the command should be “interface ten-gigabitEthernet 1/0/25”, or simply “int te 1/0/25”.